Weld Mount Stainless Steel Studs
By signing into your account, you represent that you have read and agree to our Terms and our Privacy Policy
This item is eligible for free shipping
Weld Mount Stainless Steel Panel Studs are designed to work with the entire family of Weld Mount Acrylic Adhesives. Weld Mount Stainless Steel Studs may be attached to virtually any surface for hanging panels, through deck mounts, or anywhere a sturdy mount is needed.
The Weld Mount Fastening System removes the need to install screws into or through cored substrates thus eliminating a major cause of composite delamination.
Weld Mount Studs are available in #8-32, #10-24, and 1/4-20 diameters and an assortment of lengths. See the tables below for a list of part numbers, sizes and pack quantities.
Note: Larger, heavy duty, inertial welded SS studs are also available in 5/16" and 3/8" sizes.
| Part Numbers - #8 series | Base Plate Diameter | Stud Diameter & Thread Count | Stud Length | Pack Quantity |
|---|---|---|---|---|
| WMS-PS62-832-12SS-15 | 5/8 in | #8-32 | 3/4 in | 15/pk |
| WMS-PS62-832-12SS-100 | 5/8 in | #8-32 | 3/4 in | 100/pk |
| WMS-PS62-832-16SS-15 | 5/8 in | #8-32 | 1 in | 15/pk |
| WMS-PS62-832-16SS-100 | 5/8 in | #8-32 | 1 in | 100/pk |
| WMS-PS62-832-24SS-15 | 5/8 in | #8-32 | 1-1/2 in | 15/pk |
| WMS-PS62-832-24SS-100 | 5/8 in | #8-32 | 1-1/2 in | 100/pk |
| Part Numbers - #10 series | Base Plate Diameter | Stud Diameter & Thread Count | Stud Length | Pack Quantity |
|---|---|---|---|---|
| WMS-ST125-1024-12SS-10 | 1-1/4 in | #10-24 | 3/4 in | 10/pk |
| WMS-ST125-1024-12SS-100 | 1-1/4 in | #10-24 | 3/4 in | 100/pk |
| WMS-ST125-1024-20SS-10 | 1-1/4 in | #10-24 | 1-1/4 in | 10/pk |
| WMS-ST125-1024-20SS-100 | 1-1/4 in | #10-24 | 1-1/4 in | 100/pk |
| WMS-ST125-1024-24SS-10 | 1-1/4 in | #10-24 | 1-1/2 in | 10/pk |
| WMS-ST125-1024-24SS-100 | 1-1/4 in | #10-24 | 1-1/2 in | 100/pk |
| WMS-ST125-1024-36SS-10 | 1-1/4 in | #10-24 | 2-1/4 in | 10/pk |
| WMS-ST125-1024-36SS-100 | 1-1/4 in | #10-24 | 2-1/4 in | 100/pk |
| Part Numbers - 1/4 inch series | Base Plate Diameter | Stud Diameter & Thread Count | Stud Length | Pack Quantity |
|---|---|---|---|---|
| WMS-ST125-1420-12SS-10 | 1-1/4 in | 1/4-20 | 3/4 in | 10/pk |
| WMS-ST125-1420-12SS-100 | 1-1/4 in | 1/4-20 | 3/4 in | 100/pk |
| WMS-ST125-1420-16SS-10 | 1-1/4 in | 1/4-20 | 1 in | 10/pk |
| WMS-ST125-1420-16SS-100 | 1-1/4 in | 1/4-20 | 1 in | 100/pk |
| WMS-ST125-1420-24SS-10 | 1-1/4 in | 1/4-20 | 1-1/2 in | 10/pk |
| WMS-ST125-1420-24SS-100 | 1-1/4 in | 1/4-20 | 1-1/2 in | 100/pk |
| WMS-ST125-1420-28SS-10 | 1-1/4 in | 1/4-20 | 1-3/4 in | 10/pk |
| WMS-ST125-1420-28SS-100 | 1-1/4 in | 1/4-20 | 1-3/4 in | 100/pk |
| WMS-ST125-1420-32SS-10 | 1-1/4 in | 1/4-20 | 2 in | 10/pk |
| WMS-ST125-1420-32SS-100 | 1-1/4 in | 1/4-20 | 2 in | 100/pk |
| WMS-ST125-1420-40SS-10 | 1-1/4 in | 1/4-20 | 2-1/2 in | 10/pk |
| WMS-ST125-1420-40SS-100 | 1-1/4 in | 1/4-20 | 2-1/2 in | 100/pk |
The Weld Mount Stainless Steel Studs may be bonded from either surface of the stud base plate.
Description of the WELD MOUNT ADHESIVES
AT-1030 Is A specially formulated acrylic adhesive which cures in 12 minutes and has working strength within 40 minutes. AT-1030 is packaged in a 30 ML side by side dispenser cartridge with a built in plunger. Cut off the tips and dispense the amount needed for hand mixing. A cap is included to deal the cartridge for reuse. AT-1030 is a good general purpose bonder for all substrates except low energy plastics and rubber. AT-1030 has a shelf life of 12 months when stored at 72 degrees or less. The cartridge will bond 50-75 parts.
AT-2010 is also a two-part acrylic adhesive, which is formulated with high viscosity to allow instant bonding of Weld Mount System fasteners to any surface (horizontal, vertical or overhead). AT-2010 is packaged in a two part 50 ML cartridge which is mounted in the AT-300 adhesive dispensing gun using a 1 to 1 plunger. A special mixing tip is used to mix the two components thoroughly before use. AT-2010 sets in approximately 6 minutes, develops working strength in 15-20 minutes and dries to a light yellow color. AT-2010 is used typically for bonding Weld Mount parts in lighter duty applications.
AT-4020 acrylic adhesive will bond to fiberglass, steel, aluminum, glass, wood and many other substrates. However, it should be noted that AT-4020 adhesive will not bond well to StarBoard, low energy plastics or rubber. AT-4020 does not adhere as well to metals as it does to composite substrates. Weld Mount AT-4020 Acrylic Adhesive is a specially formulated to hold studs and standoffs without sagging. The Acrylic Adhesive cures in 10 minutes and has a working strength within 30 minutes at 72 Degrees F. The 50 ML cartridge will bond approximately 100-150 parts. AT-4020 is used primarily for bonding Weld Mount parts to composites in heavier duty applications.
AT-6030 adhesive is a two-component, 10:1 mix ratio structural adhesive with outstanding adhesion for bonding metals, carbon fiber, composites and most plastics. Most metals can be bonded without priming. This advanced product is designed to meet specific requirements of the transportation industry, including reduced read through on show surfaces. The combination of minimum surface preparation, primerless metal bonding and low read through makes AT-6030 ideal for a variety of assembly operations. AT-6030 is packaged in 40ML cartridges for use with our AT-300 dispensing gun and AT-650 mixing tips. AT-6030 is used typically for bonding Weld Mount parts in the heaviest duty applications.
Technical Information
Weld Mount System advantages:
- Eliminate the need to drill in to a composite skin and exposing the core
- Eliminate drilling, tapping, welding, grinding and finishing steps
- Eliminates bonding or laying up blocks of wood to screw in conventional wire tie mounts
- Eliminate blocking added during lamination in order to have a place to put screws
- Much stronger than traditional methods