Interlux Trilux 33 Aerosol Spray Paint
By signing into your account, you represent that you have read and agree to our Terms and our Privacy Policy
This item is eligible for free shipping
Interlux Trilux 33 Aerosol Spray Paint is one of the highest performance aerosol antifouling paints available. It has been formulated specifically for aluminum outboards, outdrives and can be used on all underwater metals. Biolux Technology is used to control slime growth. Prime metal with Primocon.
Available in a 12 oz. aerosol spray in Black, Gray, and White colors.
| Drying Information | 41 degrees F | 50 Degrees F | 73 Degrees F | 95 Degrees F |
|---|---|---|---|---|
| Touch Dry (ISO) | 45 min | 30 min | 30 min | 30 min |
| Immersion | 24 hrs | 16 hrs | 12 hrs | 8 hrs |
| Overcoated By | Min-Max | Min-Max | Min-Max | Min-Max |
| TRILUX 33 Aerosol | 18 hours - | 12 hours - | 6 hours - | 4 hours- |
Preparation
BARE ALUMINUM: Sand with medium grade (grit) emery cloth to a bright metal finish. Immediately apply Viny-Lux Primewash 353/354 thinned 25% with Viny-Lux Solvent 355. Allow to dry for 1-24 hours. Apply 1 full can of Primocon Aerosol Primer YPA985 in a multi-layer procedure.
PREVIOUSLY PAINTED SURFACES: with Trilux 33 or Trilux Prop & Drive Aerosol: Sand with 80 grade (grit) paper. with Factory Finish or Antifouling Paint: Sand with 80 grade (grit) paper. Clean with Special Thinner 216. Resand any areas where bare aluminium is exposed with medium grade (grit) emery cloth and wipe clean. Apply 1 full can of Primocon Aerosol Primer YPA985 in a multi-layer procedure.
Method At least 2 coats should be applied. Hold can 12-16 inches from the unit when applying the paint. Wait for minimum overcoating time between coats. Continue until the entire can has been used per outdrive. Be sure the paint is completely dry before immersion and allow minimum immersion time.
Hints
Mixing Shake can well, listening for mixing ball. Continue shaking for at least 1 minute.
Thinner Bare Wood - Special Thinner 216.
Thinning Spray - Special Thinner 216.
Cleaner Special Thinner 216.
Airless Spray Pressure: 170-204 bar/2500-3000 psi. Tip Size: 0.53 mm/21 thou.
Conventional Spray Pressure Pot: Pressure: 3.44-4.47 bar/50-65 psi (gun pressure); 10-15 psi (pot pressure). Tip Size: 1.8-2.2 mm/70-85 thou.
Other Put extra coats of Trilux 33 Aerosol on the props and other running gear. For best antifouling protection use entire can of primer and Trilux 33e Aerosol for each lower unit.
Some Important Points Product temperature should be minimum 10 deg C/50 deg F and maximum 29 deg C/85 deg F. Ambient temperature should be minimum 10 deg C/50 deg F and maximum 35 deg C/95 deg F. Substrate temperature should be minimum 10 deg C/50 deg F and maximum 29 deg C/85 deg F.
Compatibility/Substrates Apply to clean, dry, properly prepared surfaces only. Do not apply to tin-based paint such as Micron 33, 44 or Tri-Lux IIT. Must be sealed with Primocon Aerosol YPA985.
Number of Coats 2 - Use an entire can of Trilux 33 Aerosol per lower unit.
Coverage (Theoretical) - 21.2 (sq ft/Gal)
Recommended DFT 2.0 mils dry
Application Methods Aerosol can
Technical Information
- Colors YBA068A-Black, YBS063A-White
- Finish Matte
- Typical Shelf Life 2 yrs
- Unit Size 16 fl.oz
TRANSPORTATION,STORAGE AND SAFETY INFORMATION
TRANSPORTATION: Trilux 33 Aerosol should be kept in securely closed containers during transport and storage.
STORAGE: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Trilux 33 Aerosol to be realised ensure that between use the container is firmly closed and the temperature is between 5 deg C/40 deg F and 35 deg C/95 deg F. Keep out of direct sunlight.
DISPOSAL: Container Disposal: Triple Rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill or by other procedures approved by state or local authorities. Pesticide Disposal: Open dumping is prohibited. Pesticide, spray mixture or rinsate that cannot be used or chemically reprocessed should be disposed of according to procedures approved by Federal, state, or local disposal authorities.
GENERAL: Read the label safety section for Health and Safety Information, also available from our Technical Help Line. Contains biocides. Antifoulings should only be wet sanded. Never dry sand or burn-off old antifoulings.